ASUS TX300CA Photo Guide

Disassembly Process

ASUS TX300CA Series Notebook consists of various modules. This chapter describes the procedure for the complete notebook disassembly. In addition, in between procedures, the detailed disassembly procedure of individual modules will be provided for your needs.

The disassembly procedure consists of the following steps:

  • Bottom Case Module
  • Battery Module
  • HDD Module
  • Speaker
  • IO Board
  • Motherboard Module
  • Touchpad Module
  • LCD Module

Bottom Case Module

The illustrations below show how to remove and disassemble the Top Case Module.

Remove the Bottom Case Module

1. Open latch 1 toward the arrow to take the LCD away.

2. Remove 2 rubbers and 12 screws (10 screws of M1.6*2.5 , 2 screws of M1.6*4) on the bottom case.

1. Take the bottom case away.


Battery Module

The illustration below shows how to remove the battery module.

Remove Battery Module

1. Lift up to disconnect the battery cable.

2. Remove 7 screws (7 screws of M1.6*3) on the battery module and take it away.


HDD Module

The illustrations below show how to remove and disassemble the HDD module of the notebook.

Removing the HDD

1. Remove 4 screws (4 screws of M1.6*3) on the HDD module and take it toward the arrow direction.

2. Remove 4 screws  (4 screws of M3*3) on the bracket.


Speaker Module

The illustrations below show how to remove and disassemble the speaker module of the notebook.

Removing the speaker

1. Disconnect the speaker cable.

2. Use disassembly tool to pry up the speaker of the bezel and remove the speaker toward the arrow direction.

3. Disconnect the LVDS cable.

4. Disconnect the DCIN cable.

5. Disconnect the keyboard FPC and disconnect the keyboard LED FFC.

6. Disconnect the TP FFC.


IO Board Module

The illustrations below show how to remove the IO Board from the notebook.

Remove IO Board

1. Remove 2 screws  (2 screws of M1.6*3) on the IO Board and take it away.


Motherboard Module

The illustrations below show how to disassemble and remove the Motherboard Module.

Remove the Motherboard Module

1. Remove 10 screw (10 screw of M2*5) on the LCD hinges.

2. Take the hinge cape away.

3. Remove 5 screw (3 screw of M1.6*3, 2 screw of M2*2, 2 screw of M2*5) on the motherboard and take it away.

5. Remove 4 screw (4screw of M2*2) on the DC-IN and take it away.


LCD Module

The illustrations below show how to remove and disassemble the LCD Module of the notebook.

Removing the LCD Module

1. Remove 2 screw on the LCD Module and Use disassembly tool to pry up the edge of the LCD Penal. And take the LCD away.

2. Disconnect the battery cable.

3. Remove 4 screw (4 screw of M1.6*4) on the battery and take the battery away.

4. Disconnect the antenna cable and remove 1 screw (1 screw of M1.6*3) on the Wlan. Take the WLAN Card away toward the arrow direction.

5. Remove 1 screw (1 screw of M1.6*3) on the SSD card and take it away.

6. Disconnect the LVDS cable and camera cable.

7. Disconnect the speaker cable and remove 4 screws (4 screws of M1.6*4) on the speaker.

8. Disconnect the Touch Control FFC and disconnect the Touch Control FPC.

9. Remove 2 screws (2 screws of M1*3) on the touch control board and take it away.

10. Disconnect the LED cable,  FFC cable,  fan cable.

11. Remove 4 screws (4 screws of M2*5) on the plastic and take it away.

12. Tear off 1 tape and disconnect the LVDS cable.

13. Remove 1 screws (1 screws of M2*5) on the camera and disconnect the camera cable.

14. Remove 10 screws (10 screws of M2*5) on the plastic and take it away.

15. Remove 4 screws (4 screws of M1.6*3) on the fan and take it away.

16. Remove 4 screws (4 screws of M1.6*3) on the motherboard and take it away.